SpaceFarmers.io Wiki

You've loaded an old revision of the document! If you save it, you will create a new version with this data.

===== Virtual Plots =====
Although k-32 is by far the [[https://dashboard.chia.net/d/CL1X4UWnk/blockchain-state?orgId=1&viewPanel=41|most used k-size]], chia allows us to plot big-k plots. As the number of proofs is directly proportional to the plot size in bytes, there is limited incentives on the revenue side to using larger k-plots. On the cost side however, using big k-plots offers a small advantage in terms of HDD power-saving. A k-32 has double the disk reads per byte and is accessed by the plot-filter twice more than a k-33, and four times for than a k-34, and 16 times more than a k-36, etc. One problem in leveraging these benefits has been that in order to fill up a drive to make best use of the capacity, a mixed bag of multi-k plots is required (see image below), resulting in a cost-saving that is insignificant enough to warrant a replot.

|  Drive Size  |  Plotmix  |  Available GB  |  Chiapos Space  |  GB Free  |
|  5TB  |  35,37  |  4655.82  |  4615.43  |  40.39  |
|  8TB  |  32,33,34,35,36,37  |  7449.96  |  7182.09  |  267.86  |
|  12TB  |  32,33,34,35,36,38  |  11173.45  |  11099.22  |  74.33  |
|  14TB  |  32,33,34,35,37,38  |  13036.19  |  13013.69  |  22.50  |
|  16TB  |  32,33,34,35,36,37,38  |  14898.99  |  14830.75  |  68.24  |
|  18TB  |  32,35,39  |  16760.75  |  16690.69  |  70.06  |

The Virtual Plot method tries to enhance these cost savings to the fullest, by leveraging the fact that both the plotID seed and the k-size are an input in the deterministic proof-construction of the plot format. This way, a single drive can host a variety of multiple (strictly) different k-sizes that share a single plotID, which is consulted by the plot-filter as if it were a single (hence, “virtual”)  plot. 
This means that any HDD using this matter is accessed only ~18 (9216/512) times per day with the current plot filter. This allows us to put HDDs into standby_z (spin-down) or idle_c (reduce rpm), saving 80% and 50% respectively compared to drives filled with only C0 k-32s.

Whenever a signage point arrives, you need to check the plot filter for plots passing. This plot filter check is done purely against the plotID, and is done in memory/cached, so you don't need any disk io for it. When a plot passes the plot filter, you'll need to look up qualities from the plot, that's when the disk io starts. With the current plot filter, a single plot is expected to pass only once every 512 signature points, or once every 80 minutes. 
This means that if you have an 18TB drive filled with 165 k-32s, you have 165 different plotIDs per disk and you'll have a plot passing every 30 seconds which will require disk io. The disk will not be able to sleep. If, however, you have a single plotID per disk, your disk will only have to wake once every 80 minutes. It can sleep the rest of the time, which is much more power efficient.

<WRAP center round important 90% em>
<color #001e37>
Note that standby_z leads to increased wear on spin-up. Most HDDs are rated at a limit of 50k spin-ups, so with 18 start/stop cycles a day (plot-filter 512) that would constitute ~7,6 years and with 36 start/stop cycles (plot-filter 256) you would hit the limit in ~3,8 years. 
</color>
</WRAP>

==== Who is this for ====
With the strong proliferation of compressed plots and their increased returns, why should anyone consider this method? 
For those who meet all the hardware requirements for farming compressed plots on large capacity drives, generally compression is most profitable method up to a retail electricity price of $0.25/kWh.

The virtual plot method may still be considered by a diverse set of farmers. 
A good fit would be with farmers on small drives, with high electricity prices. 
But it also allows for more complex methods, such as using idle_c during winter, while switching to standby_z in summer to reduce electricity used for AC. 
Admittedly, the plotting requirements make this method prohibitive to many. 
It is in recognition of the large variety of farmers that we try to bring attention to this method.

==== How to plot ====
Using the official ChiaPos

- create a plot using: chia plots create -k 38 -n 1 -c xxx -f yyy -x -t ... -2 ... -d ... -r <threads> -u <buckets>
  - save the plot_id and the memo displayed from the output of the first command
  - create the following plots with the same plot_id but different k-size using ProofOfSpace create -k <size> -i <plot_id> -m <memo> -f <plot_filename> -t ... -2 ... -d ...

Alternatively, plots of large k can be created using https://github.com/vladimirttt123/chiaposht.

Interested in learning more? You will find many friendly SpaceFarmers to help you in our [[https://discord.com/channels/844266352213622855/1065950234674470933|Discord]]!

==== Pooling vs Solo ====
Pool difficulty has no effect on the amount of disk spinups, as pool difficulty is only applied after the plot filter and after quality lookups. Quality lookups should cause your disk to spin up, but they are only occur before pool difficulty comes into play.

==== Proof collision ====

As mentioned earlier, a virtual plot is constructed using the fact that both the [[https://www.chia.net/wp-content/uploads/2022/09/Chia_Proof_of_Space_Construction_v1.1-1.pdf|plotID (as seed) and the k-size (k-size+4 bit-value)]] create a plot deterministically (see "Full algorithm" section). Therefore, e.g. a k-33 and a k-34 plot with the same plotID are equally different from eachother than two plots of matching k-size and a different plotID.

What's the secret key? If you don't know, please ask our admins in Discord / Telegram. Please keep this field empty:

Edit summary